- Shut off the power. Unplug the dryer to disconnect electrical power.
- Remove the back panel. Move the dryer forward and use a 1/4-inch nut driver to remove the screws from the back panel.
- Remove the fuse.
- Install the new thermal fuse.
- Reattach the back panel.
- Plug in the dryer.
- Clean the exhaust vent.
How do I reset my thermal fuse? How to Reset a Thermal Fuse Unplug the clothes dryer's power cord from the wall outlet. Swing the front panel out towards you so that you can look into the compartment. Aim a flashlight at the flat-can-like component to locate the blown thermal fuse.
will dryer start if thermal fuse is blown?Many times when a dryer's thermal fuse is blown, the dryer stops heating up the clothes when they dry. To determine whether the problem is the blown thermal fuse or something else, take out the thermal fuse and run the dryer as normal. If the dryer starts heating again, you know that your thermal fuse is blown.
Will dryer work without thermal fuse? Bypassing a Dryer Thermal Fuse Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem. Even short usage without a thermal fuse in place could result in irreparable damage to the appliance or injury to yourself.
how much does it cost to replace a thermal fuse in a dryer?
Cost of Dryer Heating Elements Heating element replacements cost between $30 and $200 dollars on average, depending on the part needed.
What causes a dryer thermal fuse to go bad? Clogged or restricted exhaust vent air flow is the most frequent cause of a thermal fuse blowing. Check the lint screen for lint or a build-up of debris that could be inhibiting air flow through the dryer. Check the flexible vent hose behind the dryer for kinks or clogs.
how do I know if my thermal fuse is blown?
Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse. If this is the case, don't fret: thermal fuse replacement is a simple task.
Does a dryer have a reset button? Many dryers are equipped with a reset button on the control panel. If the motor won't run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
What happens when thermal fuse blown on dryer?
When the fuse blows it can cause the dryer to run but not heat, or to not run at all. Most commonly the fuse will blow if there is an airflow restriction (clogged venting, lint buildup inside the dryer, ect), but it can also be caused by a shorted heating element, bad control board, and more.
Why does my dryer have no power? If your dryer won't start, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. Open the dryer door and check if the light inside the dryer turns on. If it doesn't turn on, check your power cord and the house circuit breaker.
Will a clogged dryer vent cause dryer not to heat?
Blocked venting This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow.
How do you troubleshoot a dryer?
Problem: Dryer Won't Start The door latch may not be engaging. Check the latch for lint and clean it completely so that the door closes properly. Check the power supply, including fuses and circuit breakers. Check the dryer's internal thermal fuse. If you have a push start knob, it may not be engaging correctly.
How do I test my thermostat?
Thank goodness it is much less expensive to replace a thermostat than your central heat and air unit. Check your thermostat to make sure it is in the "On" position. Stand at the thermostat while an assistant stands at the furnace. Raise the thermostat heat settings slowly. Turn off the breaker to your furnace.
Where is the thermal fuse located?
Thermal fuses are installed on the dryer's exhaust duct. Typically, you must remove the back panel of a dryer to access the fuse. Ensure to shut off electrical power to the dryer before attempting to locate and troubleshoot the fuse.
Are all dryer thermal fuses the same?
All dryers sold in the United States are legally required to have a thermal fuse. This is different from the electrical fuses that are found in many appliances, and a dryer might have both. A thermal fuse will blow when the temperature gets too high, not when it's drawing too much current.
You May Like Also